**** PLEASE NOTE ****
WE ARE NOW CLOSED FOR OUR ANNUAL EASTER BREAK
WE WILL BE BACK ON MONDAY 29th APRIL
The movements in these repair packs are our superb EZ Quartz® TICKING Quartz Clock Movements
The second hand on the ticking movements moves in 1 second steps with an audible tick
We also have EZ Quartz® SUPERSWEEP Quartz Clock Movements
The second hand on the SUPERSWEEP movement moves continuously and
the SUPERSWEEP movements are therefore much quieter than
ticking movements, although not completely silent
If you would prefer a SUPERSWEEP Movement in your repair pack please click here
Our clock repair packs contain a Quartz TICKING Clock movement, all fittings,
a choice of a short, medium or long spindle length, a battery, your choice
of hands, Full clear instructions and a 12 month Guarantee
Everything you need to make or repair a clock with confidence!
Click here to see the instructions you will receive with your clock repair pack
Many people phone us to ask "How do I repair a clock?" so we now have full instructions below
There is a bit of work invoved in repairing a clock and whilst clock repairing is not
for everyone it is usually quite easy to replace the clock movement and hands
The old movement will not be part of the repair and will have to be removed
You will then need to check a couple of dimensions to make sure that one of our movements will fit
and you will almost certainly find that the old hands will not fit the new movement
You can choose a free set of hands from our huge range and you can use our Quick Hands Viewer
to view all the patterns and their dimensions before choosing
If you are lucky and your old hands do fit then you can keep the free ones as spares!
Full instructions are supplied and dimensions of our clock movements are shown below
ALL OF OUR PRODUCTS AND ALL THE INFORMATION WE HAVE ARE ON THIS WEBSITE!
If after reading this you are not happy to attempt the repair, or if you need more information or parts that
are not shown please consult your local clock repairer or jeweller, as many jewellers repair clocks
We wish to point out (very politely!) that we are not clock repairers and we can not
mend clocks or discuss individual clock repairs over the phone or by email!
If you are happy to give it a go please read the instructions below and then order here ....
Simply choose your hands, second hand and spindle length
Full instructions and dimensions are shown below
We do have medium spindle SWEEP movements WITHOUT hangers
Please go to the SWEEP movements page
and request one in the comments box when you check out if required
The full length of the Short spindle (Movement case to tip of spindle) is 13mm
The full length of the Medium spindle (Movement case to tip of spindle) is 18mm
The full length of the Long spindle (Movement case to tip of spindle) is 21mm
The full length of the Extra Long spindle (Movement case to tip of spindle) is 29mm
Click on a picture for a better view
The diameter of the hour hand shaft is approximately 5mm and the minute hand shaft is approximately 3mm
but please note the size must be absolutely perfect. It is unlikly that your existing hands will fit
Movement dimensions
70mm high (with hanger) x 55mm wide x 16mm deep (without spindle)
The hanger can easily be removed with a hacksaw if you do not have room for it
The height if the movement without the hanger is 55mm
Centre hole needed in dial 8mm to 10mm
Our Clock Movements are available in a choice of spindle lengths
The same fittings are used regardless of spindle length
Please click the pictures for a better view
The diameter of the hour hand shaft is approximately 5mm and the minute hand shaft is approximately 3mm
but please note the size must be absolutely perfect. It is unlikly that your existing hands will fit
The full length of the Short spindle (Movement case to tip of spindle) is 13mm
The full length of the Medium spindle (Movement case to tip of spindle) is 18mm
The full length of the Long spindle (Movement case to tip of spindle) is 21mm
The full length of the Long spindle (Movement case to tip of spindle) is 26mm
Clock Repair Instructions
To mend a clock you first need to remove the existing movement and hands
They will not be needed again and it is very unlikely that your existing hands will fit the new movement
If you are lucky and they do fit, the new hands can be kept as spares
Many clocks will have the movement fitted in a different way to the new one
This doesn't matter, all you will need is the centre hole in the clock dial to be 8mm to 10mm in diameter
You can then start the repair
Click here for printable instructions on how to make or repair a clock
The brass thread is on the new movement spindle which makes assembly of the clock
very easy and provides protection to the plastic spindle.
To make a clock simply drill an 8mm to 10mm hole in the dial.
Place the rubber washer (supplied) over the movement spindle and push the
spindle through the hole from the back of the dial
Place the brass washer (supplied) over the spindle. (This covers any small chips
or ragged edges around the hole
Then just tighten the brass nut (supplied) on the thread until the movement is held firmly
Push the hour hand then the minute hand and then the second hand on to the
spindle making sure they all point to the 12
Put in the battery (supplied free with all single clock repair packs) and that’s it - your clock will start !
Tip from the ticknology dept !
We always supply a second hand with each clock movement
If you don't want to use a second hand just order a metal second hand, separate the aluminium second hand
from the brass bush and push the brass bush on to the second hand spindle to neatly cover the centre hole
IMPORTANT
OUR EZ Quartz
CLOCK MOVEMENTS AND HANDS ARE RoHS APPROVED !
Since 1st July 2006 clock movements and hands have to be RoHS approved
by law if you want to sell your clocks in the EEC
Click here to return to the main menu
ALL our prices include UK VAT and Postage
The price you see is the price you pay - and our minimum order is only £10!
You can then checkout and pay securely online or you can order online and
phone us with your card details if you prefer
We use Worldpay to securely process Maestro, Visa, Mastercard, JCB and American Express payments
PayPal payments are also welcomed
Our email address is sales@clockparts.co.uk
Please note - We operate strictly by mail order only
We do not have a shop or any facilities for visitors so we are unable
to make up orders while you wait or for collection
You can print an order form with the link below and post it to us
Click here if you would like to print an order form
You can fax your order to us on 01288 381255
Click here if you would like to print an order form
You can email us at sales@clockparts.co.uk
Please don't send your credit card details in a clear email
It is much safer to use our shopping cart or phone us
Additional Delivery Options
Next working day delivery to most UK post codes by Fedex
(when your goods are ready) for only £7.50
Please note this will not guarantee same day despatch of your order but it will save time on delivery
We can not guarantee immediate despatch of your order as many of our products are made to order
but if you need your goods urgently please phone and we will always do our best to help
Manufacturers, importers and distributors of clock materials since 1979
Where service comes first and price comes second - to none!
We are always closed for Easter week, Christmas week
and August bank holiday week