WE ARE CLOSED ON FRIDAYS
FOR EXPORT ORDERS Please click here
Full details and instructions follow below
SINGLE PENDULUM CLOCK REPAIR PACKS
IF YOU ARE REPAIRING A CLOCK PLEASE NOTE:
Whilst clock repairing is not for everyone it is often quite easy to replace the movement
and hands. You will need to measure the clock you have to check that one of our pendulum movements
will fit and you will almost certainly find that the old hands will not fit the new movement
Please make sure you select the free set of hands and that they are shown on your order confirmation
If you are lucky and your old hands do fit then you can keep the free ones as spares!
Full instructions and dimensions of our clock movements are shown below
ALL OF OUR PRODUCTS AND ALL THE INFORMATION WE HAVE ARE ON THIS WEBSITE !
If after reading this you are not happy to attempt the repair, or if you need more information or parts that
are not shown please consult your local clock repairer or jeweller, as many jewellers repair clocks
We wish to point out (very politely!) that we are not clock repairers and we can not
mend clocks or discuss individual clock repairs over the phone or by email!
If you are happy to give it a go please read the instructions below and then order here ....
Please make sure you select the hands you require
Full fitting instructions and movement dimensions are shown below
Our Pendulum /clock movements are ideal for dials up to 8mm thick
The pendulum is for decoration only and does not affect the clock movement's timekeeping
The side to side swing and the swing time of the pendulum varies according to the length and weight
of the pendulum or object you wish to swing and can even vary from movement to movement !
110mm high (without hanger)
120mm high (with hanger)
25mm deep (without spindle and without hanger)
30mm deep (with hanger)
Centre hole needed in dial 8mm to 10mm
Only available with medium spindle - ideal for dials up to 8mm thick
These pendulum / clock movements will drive any light shape making them ideal for novelty clocks
Just cut out and paint the shape of a cat in plywood and use one of our dial transfers or a set of
numerals to make the clock face. Then cut out the shape of the cat’s tail and hang it on to
the pendulum drive and the tail will swing from side to side!
Pendulum Movement fixing instructions
The brass thread is on the movement spindle which makes assembly of the clock
very easy and provides protection to the plastic hand shaft
To make or repair a clock with one of our movements you will need an 8mm to 10mm hole in the dial
Simply place the rubber washer (supplied) over the movement spindle and push the spindle through the hole from the back of the dial
Place the brass washer (supplied) over the spindle. (This covers any small chips or ragged edges around the hole
Then just tighten the brass nut (supplied) on the thread until the movement is held firmly
Push the hour hand then the minute hand and then the second hand on to the spindle making sure they all point to the 12
Put in the battery (supplied free with all single clock repair packs) and that’s it - your clock will start!
Safety and allowing space for the pendulum drive arm
A separate plastic hanger is supplied with each pendulum clock movement which can be used if required
It is best to make a strong hanger on the clock case to support your clock. If you use the detachable hanger the two connecting rods MUST be glued into the pendulum movement. The screw in the wall must be screwed in sufficiently to hold the whole movement and pendulum perfectly upright or the rod and bob will touch the wall or the clock movement and stop swinging
Tip from the ticknology dept !
If you don't want to use a second hand just order a metal second hand, separate the aluminium second hand from the brass bush and push the brass bush on to the second hand spindle to neatly cover the centre hole
Pendulum rods and bobs
If you decide to produce more traditional clocks our 250mm imitation brass pendulum rods
with 55mm imitation brass pendulum bobs will finish them off beautifully
Pendulum rod and bob prices
1 to 4 pendulums £3.25 each
5 to 9 pendulums £3 each
10 to 49 pendulums £2-75 each
50 to 99 pendulums £2-50 each
100 pendulums £2.25 each
Remember all our prices include UK VAT and UK mainland postage
The price you see is the price you pay !
ALL our prices include UK VAT and UK Postage
The price you see is the price you pay and Our Minimum Order is only £10
FOR EXPORT ORDERS Please click here
Please note - We operate strictly by mail order only
We do not have a shop or any facilities for visitors so we are unable
to make up orders while you wait or for collection
Additional Delivery Options
Next working day delivery to most UK post codes by Fedex
(when your goods are ready) for only £7.50
Please note this will not guarantee same day despatch of your order but it will save time on delivery
We can not guarantee immediate despatch of your order as many of our products are made to order
but if you need your goods urgently please phone and we will always do our best to help
Manufacturers, importers and distributors of clock materials since 1979
Where service comes first and price comes second - to none!
We are always closed for Easter week, Christmas week
and August bank holiday week